Thermal shift assay to identify compound binding to Kelch domain of Keap1 protein Measured in Biochemical System Using RT-PCR - 2119-02_Inhibitor_Dose_CherryPick_Activity
The Keap1, an oxidative stress "sensor" protein, forms a complex with the transcription factor Nrf2 and keeps Nrf2 in the cytosol for ubiquitination and subsequent proteosomal degradation. Under oxidative stress conditions, Keap1 liberates Nrf2 from its repression, resulting in an increased oxidative stress response. This response plays an important role in several diseases, including cancer, inflammation, and neurodegeneration. ..more
BioActive Compounds: 31
Kelch domain of Keap1 protein, inhibitor, binding, thermal shift assay
The Keap1, an oxidative stress "sensor" protein, forms a complex with the transcription factor Nrf2 and keeps Nrf2 in the cytosol for ubiquitination and subsequent proteosomal degradation. Under oxidative stress conditions, Keap1 liberates Nrf2 from its repression, resulting in an increased oxidative stress response. This response plays an important role in several diseases, including cancer, inflammation, and neurodegeneration.
We conducted a high throughput screen to identify inhibitor to disrupt the interaction between Keap1 and Nrf2 using biochemical fluorescence polarization assay. To confirm that the identified compounds directly bind to keap1, we developed a thermal shift assay. The thermal shift assay relays on the differential bind of a fluorescent dye Sypro Orange to the native Keap1 and to the thermal denatured Keap1. When Sypro orange is in aqueous solution and do not bind to the native Keap1, its fluorescence is largely quenched. When Sypro orange binds to the hydrophobic domain of Keap1 exposed by thermal denaturing, it emits strong fluorescence. The fluorescence signal is recorded over the time of thermal denature and the Tm is derived.
The compound that directly binds to Keap1 stablizes Keap1 and shows an Tm increase of Keap1
Protocol for thermal shift assay
Reagents and Instrument
1. Kelch domain of Keap1 protein: human recombinant Kelch domain expressed and purified from E.coli from Xtal Biostructures (X090-173)
2. Positive control: Ac-9mer-Nrf2, an acetylated 9-mer peptide from Keap1 binding region of Nrf2 from Rutgers
3. Dye: Sypro Orange 5000X from Sigma (Cat# S5692-50uL)
4. Buffer: 10mM HEPES pH7.4, 3.4mM EDTA, 150mM NaCl, 0.005% Tween-20
5. Instrument: LightCycler 480 from Roche
6. Plate: 384-well qPCR plate from Roche (Cat# 05102430001)
Solution preparation: (for a run of 22 plates)
1. Prepare 3X SyproOrange dye in buffer
Add 36uL of 5000X stock solution into 54mL buffer
2. Prepare Kelch-Dye mix solution
Add 6mL 0.83mg/mL Kelch domain protein into 54ml 3X SyproOrange dye, Mix
3. Positive control: 40uM Ac-9mer-Nrf2
Add 40uL of 10mM Ac-9mer-Nrf2 in 100% DMSO into 10mL of Kelch-Dye mixture
4. Add 200uL 100% DMSO in 50mL of Kelch-Dye mixture
1. Dispense 5uL/well of positive control to assay plate based on D39 plate map by Combi-NL (Thermo Scientific)
2. Dispense 5uL/well of Kelch-Dye solution with DMSO to the other wells of assay plate by Combi-NL (Thermo Scientific)
3. Centrifuge plate for 1min at 1,000 rpm
4. Pin 25nL/well of compound into assay plate
5. Mix with plate shaker for 5 seconds at 2,000 rpm
6. Incubate Kelch domain protein with the compounds for 10 mins at room temperature
7. Run a protein melting protocol on LightCycler 480 at temperature range of 25~85 degrees C with a ramping rate of 3.6 degrees C/min, monitoring fluorescence at the excitation of 465nm and the emission of 580nm
8. Tm value for each well was derived through Roche protein-melting analysis software.
Final screening concentration:
Sypro Orange: 3x
Compound concentration: 50-0.39uM, 8 points
PRESENCE OF CONTROLS: Neutral control wells (NC) and positive control wells (PC) were included on every plate.
EXPECTED OUTCOME: Active compounds result in increasing readout signal.
The raw signals of the plate wells were normalized using the 'Neutral Controls' method in Genedata Assay Analyzer (v10.0.2):
The median raw signal of the intraplate neutral controls (NC) is set to a normalized activity value of 0.
This was set as equal to the mean of the delta_Tm*10 rounded to closest to integer at the highest compound concentration tested. The higher the Tm shift, the higher the PUBCHEM_ACTIVITY_SCORE. Note that the score is not normalized and can be greater than 100.
Compounds that gave greater than 0.5 degree Celcius of delta_Tm at the highest compound concentration tested were declared as "Active".
Activity_Outcome = 2 (active)
Activity_Outcome = 1 (inactive)
Categorized Comment - additional comments and annotations
Assay Format: Biochemical
Assay Format: Biochemical
Assay Type: Functional
* Activity Concentration. ** Test Concentration.
Data Table (Concise)