MITF Measured in Cell-Based System Using Plate Reader - 2084-01_Inhibitor_Dose_DryPowder_Activity_Set3
The primary HTS will be performed using SK-MEL-5 melanoma cells stably expressing a construct that contains the TRPM1 promoter upstream of a luciferase reporter gene. TRPM-1 is a known target of the transcription factor, microphtalmia-associated transcription factor (MITF). The assay in its current format utilizes plating of 2000 cells per well in 384 well plates using 30 mul total volume (cells more ..
BioActive Compounds: 63
Keywords: MITF, TRPM-1, melanoma, SK-MEL-5, luciferase reporter
The primary HTS will be performed using SK-MEL-5 melanoma cells stably expressing a construct that contains the TRPM1 promoter upstream of a luciferase reporter gene. TRPM-1 is a known target of the transcription factor, microphtalmia-associated transcription factor (MITF). The assay in its current format utilizes plating of 2000 cells per well in 384 well plates using 30 mul total volume (cells plus media) per well. This will allow us to use a volume of 100 nl for pinning of the compounds 24 hours later. The cells will be incubated with test molecules for 24 hours and the luciferase activity will be detected using 20 mul per well of the Steady Glo Reagent from Perkin Elmer. The positive control is parthenolide which is known to decrease TRPM-1 expression and kill melanoma cells.
Compounds that inhibit MITF directly or indirectly will reduce the expression of TRPM-1 expression and lead to a reduction in luminescence signal. Compounds that increase the activity of MITF or somehow lead to increased expression of TRPM-1 will lead to an increase in luminescence signal.
MITF Primary Screening Protocol
(TRPM-1 Promoter//Luciferase reporter assay)
Day 1, plate TRPM-1 luc/SKMEL5 cells at 2000 per well in 30 uL media (phenol red free DMEM/10% heat inactivated Fetal Bovine Serum/Penicillin/Streptomycin/L-Glutamine)
Day 2, pin 100 nL compound/DMSO solution into 30 uL assay volume in white, opaque Corning 8867 barcoded 384 well plates. (For HTS, will require sentinel pinning with the positive control, parthenolide)
Incubate 24 hours at 37 degrees C in Liconic incubator.
Day 3, add 20 uL 100% Promega SteadyGlo per well with Thermo Combi fluid transfer apparatus.
Shake 15 seconds on "big bear" plate shaker and incubate at room temperature for 5 minutes.
Read on the Perkin-Elmer EnVision plate reader with ultra-sensitive luminescence (US LUM) settings for 0.5 sec per well
PRESENCE OF CONTROLS: Neutral control wells (NC; n=104) and positive control wells (PC; n=20) were included on every plate.
EXPECTED OUTCOME: Active compounds result in decreasing readout signal.
ACTIVE CONCENTRATION LIMIT:
For each sample, the highest valid tested concentration (Max_Concentration) was determined and the active concentration limit (AC_limit) was set to equal (2)(Max_Concentration).
The raw signals of the plate wells were normalized using the 'Neutral Controls Minus Inhibitors' method in Genedata Assay Analyzer (v7.0.3):
The median raw signal of the intraplate neutral control wells was set to a normalized activity value of 0.
The median raw signal of the intraplate positive control wells was set to a normalized activity value of -100.
Experimental wells values were scaled to this range.
PATTERN CORRECTION: The plate pattern correction algorithm 'Runwise Pattern (Multiplicative)' in Genedata (v7.0.3) was applied to the normalized plate data.
MEASUREMENT USED TO DETERMINE ACTIVE CONCENTRATION (AC): AC50
AC values were calculated using the curve fitting strategies in Genedata Screener Condoseo (7.0.3).
AC values were calculated up to the active concentration limit described for each sample.
pAC was set to equal -1*log10(AC)
Activity_Outcome = 1 (inactive) when:
a) compound shows activity but in a direction opposite to the expected outcome
in these cases, values describing curve fitting parameters (Sinf, S0, Hill Slope, log_AC50, log_AC50_SE) are set to null
b) curve fit is constant where activity is > -30% and < 30% at all tested concentrations, or
c) AC > AC_limit
Activity_Outcome = 2 (active) when:
AC <= AC_limit
Activity_Outcome = 3 (inconclusive) when:
a) Curve fitting strategy resulted in a constant fit with activity >= -70% but <= -30%, or
b) The fit was deemed not valid due to poor fit quality.
If PUBCHEM_ACTIVITY_OUTCOME = 1 (inactive) or 3 (inconclusive),
then PUBCHEM_ACTIVITY_SCORE = 0
If PUBCHEM_ACTIVITY_OUTCOME = 2 (active)
then PUBCHEM_ACTIVITY_SCORE = (10)(pAC)
Scores relate to AC in this manner:
120 = 1 pM
90 = 1 nM
60 = 1 uM
30 = 1 mM
0 = 1 M
When the active concentration (AC) is calculated to be greater than the highest valid tested concentration (Max_Concentration), the PUBCHEM_ACTIVITY_SCORE is calculated using Max_Concentration as the basis.
When the active concentration (AC) is calculated to be less than the lowest tested concentration, the PUBCHEM_ACTIVITY_SCORE is calculated using the lowest tested concentration as the basis.
The individual dose data point columns ('Activity_at_xxuM') reported here represent the median of valid (unmasked) replicate observations at each concentration. These values are the inputs to a curve fitting algorithm.
All other data columns represent values which are derived during the curve fitting algorithm; this may sometimes include automatic further masking of some replicate data points.
Occasionally this results in perceived inconsistencies: for example, between the derived 'Maximal_Activity' and the apparent most active data point.
Categorized Comment - additional comments and annotations
* Activity Concentration. ** Test Concentration.
Data Table (Concise)