Reversing Antifungal Drug Resistance Measured in Microorganism System Using Plate Reader - 2037-01_Inhibitor_Dose_DryPowder_Activity_Set2
Assay Overview: The basic assay strategy will consist of fluconazole-resistant C. albicans clinical isolate cultured in microtiter plates in the presence of a sub-toxic concentration of fluconazole. Test compounds that inhibit subsequent growth in the presence of fluconazole will merit further evaluation for their synergy with fluconazole. This whole cell phenotypic screening approach will only more ..
BioActive Compounds: 12
Depositor Specified Assays
Keywords: Candida albicans, drug resistance, fluconazole, Hsp90, Calcineurin, stress response
Broad Institute: Reversing Antifungal Drug Resistance
Project ID: 2037
Primary Collaborators: Susan Lindquist, Whitehead Institute for Biomedical Research, firstname.lastname@example.org
Assay Overview: The basic assay strategy will consist of fluconazole-resistant C. albicans clinical isolate cultured in microtiter plates in the presence of a sub-toxic concentration of fluconazole. Test compounds that inhibit subsequent growth in the presence of fluconazole will merit further evaluation for their synergy with fluconazole. This whole cell phenotypic screening approach will only capture compounds that retain activity in biological media and are capable of entering and accumulating in fungi to bioactive concentrations. Grossly cytotoxic compounds will be removed through subsequent counterscreens. Compound activity will be measured by the metabolism of Alamar Blue, a cell stain that is metabolized to a fluorescent product by living cells but that remains non-fluorescent in wells with growth-inhibited organisms.
a. Compounds that inhibit yeast growth in the presence, but not in the absence of 8 ug/ ml fluconazole.
b. Compounds that show a 10-fold specificity between the primary Candida test strain and mammalian cells.
c. Compounds that exhibit 10X greater inhibition against fungus than the hsp90 chaperone and /or calcineurin.
d. IC50 < 1uM
Expected Outcome: Active wells will show a reduced fluorescence intensity due to a reduction in the amount of Alamar Blue dye metabolized by fewer viable microorganisms.
Geldanamycin (GA) 15mM stock solution in DMSO
Fluconazole (FLC, Sequoia Research Products Ltd) 2 mg/ml stock solution in PBS
Pen/Strep 100x in PBS
Synthetic Defined Growth Medium
RPMI 1640 medium, (powder without sodium bicarbonate; Invitrogen 31800-089)
Uridine 8 mg/ml in water (Sigma)
Glucose 40% (w/v) in water (Sigma)
MOPS Buffer (Sigma)
Test Strain: C. albicans CaCi-2 (Redding et al., 1994, Clin Infect Dis 24:235-247)
Inoculate 500 ul of strain from cryopreserved stock into 250 ml shaker flask containing 30 ml growth medium. Shake at 30 degrees C overnight.
Read OD 600 of fungal culture using standard plate reader. Dilute to starting OD of the fungal inoculum of 0.00015 A600.
384 well black sterile Corning plates (PN 3712)
Prepare Geldanamycin positive control solution:
1 ml 15mM stock solution Geldanamycin
4 ml RPMI Growth Medium
20 ul Fluconazole stock solution
50 ul Pen/Strep
Dispense 400 nL into positive control wells using Combi NL (Thermo.)
Add fluconazole stock solution (2 mg/mL in PBS) to fungal inoculum to achieve 8 ug/ml. Add Pen/Strep at 0.1 ml per 10 ml media.
Using Combi, dispense 40 uL/well of fungal suspension into all wells.
Pin 25 nL from compound plates into assay plates.
Incubate plates in humidified (90 % humidity) incubator at 37 degrees C without agitation for 48 hrs.
Dilute Alamar Blue Reagent (Biosource International Cat# DAL1100) 1:40 in Ca/Mg-free PBS. Add 5 ul/well to plates with Combi NL (final dilution factor 1:200). Incubate 2 hrs at room temperature. Read Relative Fluorescence Intensity (RFU) of wells on standard plate reader as measure of relative fungal growth.
Plate reader set-up- Envision, Perkin Elmer: Ex 544nm, Em 590nm, Bandwidth 12nm, Top read.
PRESENCE OF CONTROLS: Neutral control wells (NC) and positive control wells (PC) were included on every plate.
EXPECTED OUTCOME: Active compounds result in decreasing readout signal.
ACTIVE CONCENTRATION LIMIT:
For each sample, the highest valid tested concentration (HVC) was determined and the active concentration limit (AC_limit) was set to equal (10)(HVC).
The raw signals of the plate wells were normalized using the 'Neutral Controls Minus Inhibitors' method in Genedata Assay Analyzer (v7.0.3):
The median raw signal of the intraplate neutral control wells was set to a normalized activity value of 0.
The median raw signal of the intraplate positive control wells was set to a normalized activity value of -100.
Experimental wells values were scaled to this range.
PATTERN CORRECTION: No plate pattern correction algorithm from Genedata Condoseo (v.7.0.3) was applied.
MEASUREMENT USED TO DETERMINE ACTIVE CONCENTRATION(AC): EC50
AC values were calculated using the curve fitting strategies in Genedata Screener Condoseo (7.0.3).
AC values were calculated up to the active concentration limit described for each sample.
Activity_Outcome = 1 (inactive) when:
a) curve fit is constant where activity is > -30% and < 30% at all tested concentrations, or
b) AC > AC_limit, or
c) compound shows activity but in a direction opposite to the expected outcome
in these cases, values describing curve fitting parameters (Sinf, S0, Hill Slope, log_AC50, log_AC50_SE) are set to null
Activity_Outcome = 2 (active) when:
AC <= AC_limit
Activity_Outcome = 3 (inconclusive) when:
a) Curve fitting strategy resulted in a constant fit with activity >= -70% but <= -30%, or
b) The fit was not valid due to poor fit quality.
PUBCHEM_ACTIVITY_SCORE = 0 when PUBCHEM_ACTIVITY_OUTCOME = 1 (inactive) or 3 (inconclusive)
PUBCHEM_ACTIVITY_SCORE = (-10)[Log(AC)], where AC is in molar, when PUBCHEM_ACTIVITY_OUTCOME = 2 (active)
Scores relate to AC in this manner:
120 = 1 pM
90 = 1 nM
60 = 1 uM
30 = 1 mM
0 = 1 M
PUBCHEM_ACTIVITY_SCORE = 100 when the curve fit is constant and showing full inhibition at all tested concentrations.
The individual dose data point columns ('Activity_at_xxuM') reported here represent the median of valid (unmasked) replicate observations at each concentration. These values are the inputs to a curve fitting algorithm.
All other data columns represent values which are derived during the curve fitting algorithm; this may sometimes include automatic further masking of some replicate data points.
Occasionally this results in perceived inconsistencies: for example, between the derived 'Maximal_Activity' and the apparent most active data point.
* Activity Concentration. ** Test Concentration.
Data Table (Concise)